I just purchased a nice used Dell 3115cn multifunction printer. I have printing, faxing and scanning working just fine. The only thing I cannot get working is the built in wireless adapter. In order tho set up the wireless adapter I need the 3115cn UM078 Installation CD that came with the printer. I did not receive the installation CD when I purchased the used Dell printer.
Can someone direct me as to how I might obtain just the setup/installation portion of the disk to be able to set up my Dell wireless on this printer? I do understand that I cannot obtain the entire contents of the CD because of the licensed ScanSoft PaperPort application that is included on the disk. Again I do not need anything but the files to set up the 3115cn built in wireless.
Hopefully someone on this forum or a Dell employee can point me the right direction to be able to obtain the needed wireless set up files.
Any help or direction is appreciated.
Thank you for your reply.
I have responded to your query through private message. Kindly check and reply if you have further queries.
Thanks and regards,Babita S#iworkforDell
For easy access to drivers, manuals and product updates, please visit our Support Site .
Hi Scott H,
Welcome to Dell Community Forum.
The Dell Wireless USB 3310 Printer Adapter adds wireless networking capability to the Dell 3115cn color laser printers. The drivers to use the adapter are included with the printer drivers and utilities software. The Wireless USB 3310 Adapter connects to the Multi-Protocol Card (MPC), therefore the MPC must already be installed in the printer.
You have correctly mentioned that the printer drivers cd is required for the same however, since you do not have the cd, try downloading and installing the printer software from the Dell Support Website. The links mentioned below may be useful in this regard.
For Dell 3115cn drivers and User Guide : http://dell.to/13frl3p
For information on connecting the Dell 3115cn to a Wireless Network: http://dell.to/12FHk6v
For installing the Dell Wireless USB 3310 Adapter: http://dell.to/12tkCzA
Hope this helps resolve the issue for you. Let me know if further help is needed.
Hi Babita S.
Thanks for the response to my question about obtaining the needed installation files to be able to set up the 3115cn wireless adapter. The three links you provide all have very good information for installing the USB 3310 Adapter, but none of the links provide any way to obtain the needed files that are only on the 3115cn UM078 Installation CD. The links you provide all start with:
Insert the Dell Laser Printer Drivers & Utilities CD in a system on the network.The Dell Printer Installation setup window appears.
I have looked at every driver link I can find at the Dell web site and nowhere can I find the needed set up files for the wireless. The driver links contain all other needed drivers, but not the needed setup files for the wireless adapter.
Is their any other way for me to obtain the needed files to be able to set up the 3115cn wireless adapter?
Thanks again for the help!
Hi Scott H.,
The software that you are looking for is a complementary software that is only shipped at the point of purchase of the printer. Try to contact the original owner of the printer for the cd, if possible.
Or, if you know somebody who owns a similar printer and has the printer installation cd, you can use the same to install the printer drivers. I know these are workarounds which may or may not be possible but unfortunately, if the drivers on the Support website did not prove helpful then, these are the only options available.
I have contacted the original owner of the printer and I was told the CD was not available. The printer was purchased from Dell as a refurbished / used printer and I was told the installation CD did not come with the printer. I also do not know anyone else whom owns this model of Dell printer.
I have responded to your request for additional information about my printer. Thank you for anything you can do in this matter.
I have the same issue. I have a Dell 3115cn Laser Printer with the WLA3310 USB Wireless adapter. When I changed my home wireless network it quit working. I inserted the cd but it now longer works. I am not able to find the installer file to run the needed steps listed in the following articles. Please advise. Thanks
I bought my 3115cn from Dell in 2009. I just bought the hardware to add wireless capability. I had the CD but have moved twice. I don't have a clue where it is or even if I have it. There must be somewhere to download this file. Help please!!
THE ANSWER (at least this works for me)!!!! I was trying to connect my 3115cn to my "regular" wireless network but could not figure out how to change the SSID in the printer. That is a futile effort without the utility program - here is an alternative. The result is you will have two wireless networks - your "regular" wireless network and a network specific to the 3115cn. If you print while connected to your "regular" wireless network, the 3115cn netowrk will connect on an "on demand" basis without disturbing your regular network. Here goes:
1. From the printer control panel (PCP) - reinitialize the non-volatile memory (NVM) under the Wireless Network section (this wipes out any residual wireless info);
2. Also from the PCP print a System Report - check to ensure the multi-protocol card and the USB adapter are recognized under Printer Options section of the report. If not, stop here because your system is not seeing the wireless hardware. If those are listed look under the Wireless Network section. You should see the IP address as 0.0.0.0. Also look at Wireless Network section of the report for the current SSID. Mine was "dell_device" ( that is probably what yours will read too, in any event make note of the listed SSID);
3. "View Available Wireless Networks" on your PC. Find the network with the same SSID as your printer. Connect to that network. The "Acquiring Network Address" message appears - it seemed to take longer than usual but my system connected after a minute or so;
4. From the PCP, print another System Report. You should see that an IP address now appears in the Wireless Network section of the report. Make note of that IP address;
5.Connect printer to the PC with a USB cable. The printer should install and appear on your list of available printers (at this point it is still just a USB printer);
6.Right click on the 3115cn printer and bring up the Printer Properties;
7. Go to the Ports tab;
8. Add a Port using the Standard TCP/IP port type; click next and the Add Port Wizard will ask for an IP address - enter the IP address from the Wireless Network section of the System Report you printed in Step 4 above.
9. Select this new port as the port for the 3115cn printer;
10. Unplug the USB cable; your printer is now a wireless printer with its own SSID
11. If your "regular" wireless network is unconnected at this point, you can connect to your "regular" wireless network; You will see that the printer network (SSID = dell_device in my case) does not disconnect - it simply says On Demand;
12. When you print, the printer network connects "on demand" and when the print job is done that connection goes back to a waiting state "On Demand"
Like I said, works for me. I hope it works for you.
P.S. One clarification - "On Demand" networks do not automatically spring to life when a print job is sent to the computer - at least not that I can see so far. A little clunky but the routine is as follows when already connected to your "regular" wireless network: 1. Go to "View Available Wireless Networks"; Click on your printer's "On Demand" network (no need to disconnect from your "regular" wireless network); when connected, send your print job; go back to "View Available Wireless Networks"; connect to your regular wireless network. If anyone knows of a more automated way to switch networks or have both "always on" feel free to chime in
P.P.S. Rather than rewrite the above, I will add so the development of my thought process is clear - that may be easier to track than a quick jump to the answer. After writing the P.S. it occurred to me that I have a dual band router. Perhaps, I can have my "regular" network operate on the 5 MHZ band and the printer on the 2.4 MHZ band. I'm not sure how to do this - perhaps by locking in the transmit channels.
P.P.P.S. (May 14, 2014) - When writing the above, I could not get the printer to connect to my regular wireless network hence I went with the two network approach described above (ad hoc for the printer, infrastructure for everything else). The wireless LAN setting on the 3115cn configuration page (accessible when the ad hoc netowrk is set-up as above) allows me to change the SSID and pass phrase but would never connect. Eventually, I figured out the problem - I had been selecting WPA-AES as the printer's security mode when I should have picked WPA-TKIP. Once I made that change, and reset my printer's wireless to my regular SSID, infrastructure amd pass phrase, my printer is connected full time to my wireless network. So, I now have a fully capable (printing and scanning) wireless 3115cn without having the utilities CD. Whew! Over and out . . .
Please click on this link for all Dell Laser Printer issues: http://dell.to/1nsObRl
If installing on Windows 8, please click on this link: http://dell.to/1oqJxD7
Let us know if you need further assistance, we would be happy to assist.
Thanks and regards.Babita S #iworkfordell
To know more about Dell Product Support, Drivers & Downloads, Order & Dispatch status -> choose your region US Customers; UK Customers; India Customers. For Dell support videos click Here.
We hope the links were helpful.
Please reply if you need further assistance, we would be happy to assist.